شركة انجاز لتصميم وتطوير المواقع الإلكترونية

النتائج 1 إلى 7 من 28

الموضوع: Design And Construction Of Axial Slow Flow Cw Co2 Laser

Hybrid View

  1. #1
    مشرفة سابقة
    Array الصورة الرمزية ماجستير هندسة ليزر
    تاريخ التسجيل
    Mar 2007
    الدولة
    العراق-بغداد
    العمر
    38
    المشاركات
    481
    شكراً
    0
    شكر 0 مرات في 0 مشاركات
    معدل تقييم المستوى
    216

    مشاركة: Design And Construction Of Axial Slow Flow Cw Co2 Laser

    chapter two

    2.8i CO2 Laser System Configuration:

    Three CO2 laser system configurations have been built in this project . The first configuration in our work (as shown in figure 2.6) consist from higher reflected electrode works as an anode terminal and output coupler electrode works as cathode terminal with one plasma discharge tube 0.75m long joining between them. The above system represented only one fold laser type.i

    The second configuration consists from three blocks HR electrode and OC electrode both of them works as cathode terminal and the third block is the Bakelite electrode, which has two-anode pins terminal..i

    There are two double jacket discharge tubes represent optical active medium joining between the two aluminum electrode with Bakelite terminal (see figure 2.7)..i

    In both of the above system we have been used the same hemispherical resonator consist from plane, 60% ZnSe (OC)output coupler mirror and 10 m radius of curvature gold coated mirror as HR back mirror..i

    The third and last configuration is the (v-configuration) which consists of two parallel folds, which consist from four electrodes. OC electrode and HR electrode both of them works as anode and joining the corner holder tubes electrode, which represent cathode by two discharge tubes..i

    Then the corner holder tubes electrode connected with corner electrode by using Pyrex tube of 0.6m outer diameter and length of 0.8m(see figure 2.8).In this system we use the same hemispherical resonator with adding Gold coated plane mirror in the corner electrode use just as reflector..i

    In the above three systems configuration we use the same CO2 gas mixture and cooled by the same chiller..i

    HeNe laser has been used to perform the mirror alignment and we do the initial alignment once every thing for each part of the system and after evacuating the system..i


    .Figure 2.6: Picture of One Fold of The System



    Fig.2.7: Two Folds CO2 Laser System as Being Builds in the Lab..i




    Figure 2.8: Corner Electrode Joining with Holder Tubes Electrode..i


    انتهى الفصل الثاني

    ان شاء الله الفصل الثالث ياتيكم لاحقا

    سلامي لكم
    التعديل الأخير تم بواسطة ماجستير هندسة ليزر ; 10-09-2007 الساعة 11:04 PM

    وطنُ مدا على الافق جناحا ارتدى مجد الحضارات وشاحا
    بوركت ارض الفراتين وطن عبقريا المجد بعزمًا وسماحا

معلومات الموضوع

الأعضاء الذين يشاهدون هذا الموضوع

الذين يشاهدون الموضوع الآن: 1 (0 من الأعضاء و 1 زائر)

المواضيع المتشابهه

  1. laser
    بواسطة aly otaifi في المنتدى فكر فيزيائياً
    مشاركات: 1
    آخر مشاركة: 12-31-2010, 12:44 AM
  2. The properties of LASER
    بواسطة ماجستير هندسة ليزر في المنتدى منتدى فيزياء الليزر وتطبيقاته
    مشاركات: 8
    آخر مشاركة: 12-12-2010, 06:44 AM
  3. Current Flow in Ohmic Resistors
    بواسطة رجب مصطفى في المنتدى منتدى الإلكترونيات والفيزياء الإلكترونية
    مشاركات: 0
    آخر مشاركة: 04-23-2009, 11:34 PM
  4. Current Flow in Ohmic Resistors
    بواسطة رجب مصطفى في المنتدى منتدى الفيزياء الكهربية والمغناطيسية
    مشاركات: 0
    آخر مشاركة: 04-23-2009, 11:34 PM

مواقع النشر (المفضلة)

مواقع النشر (المفضلة)

ضوابط المشاركة

  • لا تستطيع إضافة مواضيع جديدة
  • لا تستطيع الرد على المواضيع
  • لا تستطيع إرفاق ملفات
  • لا تستطيع تعديل مشاركاتك
  •